Theoretically Designed Cu10 Sn3 -Cu-SnOx as Three-Component Electrocatalyst for Efficient and Tunable CO2 Reduction to Syngas.

Electrocatalytic transformation of CO2 to various syngas compositions is an exceedingly attractive approach to carbon-neutral recycling. Meanwhile, the achievement of selectivity, stability, and tunability of product ratios using single-component electrocatalysts is challenging. Herein, the theoretically-assisted design of the triple-component nanocomposite electrocatalyst Cu10 Sn3 -Cu-SnOx that addresses this challenge is presented. It is shown that Cu10 Sn3 is a valuable electrocatalyst for suitable CO2 reduction to CO, SnO2 for CO2 reduction to formate at large overpotentials, and that the Cu-SnO2 interface facilitates H2 evolution. Accordingly, the interaction between the three functional components affords tunable CO/H2 ratios, from 1:2 to 2:1, of the produced syngas by controlling the applied potentials and relative contents of functional components. The syngas generation is selective (Faradaic efficiency, FE = 100%) at relatively lower cathodic potentials, whereas formate is the only liquid product detected at relatively higher cathodic potentials. The theoretically guided design approach therefore provides a new opportunity to boost the selectivity and stability of CO2 reduction to tunable syngas.

Metal-Organic Framework-Derived ZnO, N Dually Doped Nanocages as an Efficient Host for Stable Li Metal Anodes.

The drastic volume expansion and dendrite growth of lithium metal anodes give rise to poor electrochemical reversibility. Herein, ZnO, N dually doped nanocages (c-ZNCC) were synthesized as the host for lithium metal anodes using the zeolitic imidazolate framework-8 (ZIF-8). The synthesis is based on a two-step core@shell evolution mechanism, which could guide lithium deposition rapidly and offer a fast lithium-ion diffusion during the cycling process. Benefiting from the unique design, the as-obtained c-ZNCC can render a record short lithium infusion as low as 1.5 s, a stable lithium stripping/plating capability as long as 3000 h, and a voltage hysteresis of 95 mV when cycling at 10 mA cm-2 to 10 mA h cm-2. A low Tafel slope of 3.45 mA cm-2 demonstrates the efficient charge transfer of c-ZNCC-Li, and the galvanostatic intermittent titration technique measurement shows high diffusion coefficient of c-ZNCC-Li during the charging process. In addition, the LNMO||c-ZNCC-Li cell exhibits a capacity retention as high as 93.7% at 1 C after 200 cycles. This work creates a new design for deriving nanocages with dual lithiophilic spots using a metal-organic framework and carbon cloth for favorable Li metal anodes.

Insights into Electrochemical CO2 Reduction on SnS2 : Main Product Switch from Hydrogen to Formate by Pulsed Potential Electrolysis.

Tin disulfide (SnS2 ) is a promising candidate for electrosynthesis of CO2 -to-formate while the low activity and selectivity remain a great challenge. Herein, we report the potentiostatic and pulsed potential CO2 RR performance of SnS2 nanosheets (NSs) with tunable S-vacancy and exposure of Sn-atoms or S-atoms prepared controllably by calcination of SnS2 at different temperatures under the H2 /Ar atmosphere. The catalytic activity of S-vacancy SnS2 (Vs -SnS2 ) is improved 1.8 times, but it exhibits an exclusive hydrogen evolution with about 100 % FE under all potentials investigated in the static conditions. The theoretical calculations reveal that the adsorption of *H on the Vs -SnS2 surface is energetically more favorable than the carbonaceous intermediates, resulting in active site coverage that hinders the carbon intermediates from being adsorbed. Fortunately, the main product can be switched from hydrogen to formate by applying pulsed potential electrolysis benefiting from in situ formed partially oxidized SnS2-x with the oxide phase selective to formate and the S-vacancy to hydrogen. This work highlights not only the Vs -SnS2 NSs lead to exclusively H2 formation, but also provides insights into the systematic design of highly selective CO2 reduction catalysts reconstructed by pulsed potential electrolysis.

Janus (Mo/ß-Mo2C)@C heterostructure as an efficient electrocatalyst for the hydrogen evolution reaction in acidic and alkaline media.

To explore low-cost, high-efficiency, and noble-metal-free catalysts for electrocatalytic water splitting in both acidic and alkaline media, the metal-metal carbide Janus hierarchical structure comprising Mo andß-Mo2C embedded on a carbon layer (Mo/ß-Mo2C)@C is synthesized by a hydrothermal reaction and subsequent low-temperature magnesium thermic process. Systematic characterization by XRD, XPS, Raman scattering, and SEM/TEM reveals the successful formation of metallic Mo andß-Mo2C nanoparticles. The synthesized (Mo/ß-Mo2C)@C has a large specific surface area and boasts highly efficient hydrogen evolution reaction activity including low overpotentials of 152 and 171 mV at a current density of 10 mA cm-2and small Tafel slopes of 51.7 and 63.5 mV dec-1in acidic and alkaline media, respectively. In addition, the catalyst shows outstanding stability for 48 h in both acidic and alkaline media. The excellent catalytic activity originates from more active sites and greater electron conductivity bestowed by the carbon layer, which also improves the long-term stability in both acidic and alkaline solutions.

Highly Durable and Efficient Ni-FeOx/FeNi3 Electrocatalysts Synthesized by a Facile In Situ Combustion-Based Method for Overall Water Splitting with Large Current Densities.

Ni-/Fe-based materials are promising electrocatalysts for the oxygen evolution reaction (OER) but usually are not suitable for the hydrogen evolution reaction (HER). Herein, a durable and bifunctional catalyst consisting of Ni-FeOx and FeNi3 is prepared on nickel foam (Ni-FeOx/FeNi3/NF) by in situ solution combustion and subsequent calcination to accomplish efficient alkaline water splitting. Density functional theory (DFT) calculation shows that the high HER activity is attributed to the strong electronic coupling effects between FeOx and FeNi3 in the Janus nanoparticles by modulating ΔGH* and electronic states. Consequently, small overpotentials (η) of 71 and 272 mV in HER and 269 and 405 mV in OER yield current densities (j) of 50 and 1000 mA cm-2, respectively. The catalyst shows outstanding stability for 280 and 200 h in HER and OER at a j of ∼50 mA cm-2. Also, the robustness and mechanical stability of the electrode at an elevated j of ∼500 mA cm-2 are excellent. Moreover, Ni-FeOx/FeNi3/NF shows excellent water splitting activities as a bifunctional catalyst as exemplified by j of 50 and 500 mA cm-2 at cell voltages of 1.58 and 1.80 V, respectively. The Ni-FeOx/FeNi3/NF structure synthesized by the novel, simple, and scalable strategy has large potential in commercial water electrolysis, and the in situ combustion method holds great promise in the fabrication of thin-film electrodes for different applications.

Enhanced photocatalytic degradation of 4-chlorophenol under visible light over carbon nitride nanosheets with carbon vacancies.

Two-dimensional graphitic carbon nitride (g-C3N4, GCN) is considered as one of the promising visible light-responsive photocatalysts for energy storage and environmental remediation. However, the photocatalytic performance of pristine GCN is restricted by the inherent shortcomings of rapid charge carrier recombination and limited absorption of visible light. Vacancy engineering is widely accepted as the auspicious approach for boosting the photocatalytic activity of GCN-based photocatalysts. Herein, a magnesium thermal calcination method has been developed to reconstruct GCN, in which magnesium serves as a carbon etcher for introducing carbon vacancies and pores into GCN (Vc-GCN). The fabricated Vc-GCN demonstrates excellent photocatalytic performances of degrading hazardous 4-chlorophenol under visible light irradiation benefiting from the improved carrier separating and light absorption ability as well as rich reactive sites. The optimal Vc-GCN sample delivers 2.3-fold enhancement from the pristine GCN. The work provides a tactic to prepare GCN photocatalysts with controllable carbon vacancies and for a candidate for the degradation of organic pollutants from the environment.

Nonleaching Antibacterial Concept Demonstrated by In Situ Construction of 2D Nanoflakes on Magnesium.

In bone implants, antibacterial biomaterials with nonleaching surfaces are superior to ones based on abrupt release because systemic side effects arising from the latter can be avoided. In this work, a nonleaching antibacterial concept is demonstrated by fabricating 2D nanoflakes in situ on magnesium (Mg). Different from the conventional antibacterial mechanisms that depend on Mg2+ release and pH increase, the nanoflakes exert mechanical tension onto the bacteria membranes to destroy microorganisms on contact and produce intracellular stress via physical interactions, which is also revealed by computational simulations. Moreover, the nanoflake layer decelerates the corrosion process resulting in mitigated Mg2+ release, weaker alkalinity in the vicinity, and less hydrogen evolution, in turn inducing less inflammatory reactions and ensuring the biocompatibility as confirmed by the in vivo study. In this way, bacteria are killed by a mechanical process causing very little side effects. This work provides information and insights pertaining to the design of multifunctional biomaterials.

Recent Advances in Electrocatalytic Hydrogen Evolution Using Nanoparticles.

Hydrogen fuel is considered as the cleanest renewable resource and the primary alternative to fossil fuels for future energy supply. Sustainable hydrogen generation is the major prerequisite to realize future hydrogen economy. The electrocatalytic hydrogen evolution reaction (HER), as the vital step of water electrolysis to H2 production, has been the subject of extensive study over the past decades. In this comprehensive review, we first summarize the fundamentals of HER and review the recent state-of-the-art advances in the low-cost and high-performance catalysts based on noble and non-noble metals, as well as metal-free HER electrocatalysts. We systemically discuss the insights into the relationship among the catalytic activity, morphology, structure, composition, and synthetic method. Strategies for developing an effective catalyst, including increasing the intrinsic activity of active sites and/or increasing the number of active sites, are summarized and highlighted. Finally, the challenges, perspectives, and research directions of HER electrocatalysis are featured.

Photocatalytic water splitting by N-TiO2 on MgO (111) with exceptional quantum efficiencies at elevated temperatures.

Photocatalytic water splitting is attracting enormous interest for the storage of solar energy but no practical method has yet been identified. In the past decades, various systems have been developed but most of them suffer from low activities, a narrow range of absorption and poor quantum efficiencies (Q.E.) due to fast recombination of charge carriers. Here we report a dramatic suppression of electron-hole pair recombination on the surface of N-doped TiO2 based nanocatalysts under enhanced concentrations of H+ and OH-, and local electric field polarization of a MgO (111) support during photolysis of water at elevated temperatures. Thus, a broad optical absorption is seen, producing O2 and H2 in a 1:2 molar ratio with a H2 evolution rate of over 11,000 µmol g-1 h-1 without any sacrificial reagents at 270 °C. An exceptional range of Q.E. from 81.8% at 437 nm to 3.2% at 1000 nm is also reported.

An antibacterial platform based on capacitive carbon-doped TiO2 nanotubes after direct or alternating current charging.

Electrical interactions between bacteria and the environment are delicate and essential. In this study, an external electrical current is applied to capacitive titania nanotubes doped with carbon (TNT-C) to evaluate the effects on bacteria killing and the underlying mechanism is investigated. When TNT-C is charged, post-charging antibacterial effects proportional to the capacitance are observed. This capacitance-based antibacterial system works well with both direct and alternating current (DC, AC) and the higher discharging capacity in the positive DC (DC+) group leads to better antibacterial performance. Extracellular electron transfer observed during early contact contributes to the surface-dependent post-charging antibacterial process. Physiologically, the electrical interaction deforms the bacteria morphology and elevates the intracellular reactive oxygen species level without impairing the growth of osteoblasts. Our finding spurs the design of light-independent antibacterial materials and provides insights into the use of electricity to modify biomaterials to complement other bacteria killing measures such as light irradiation.

Development of a novel tridentate ligand for colorimetric detection of Mn2+ based on AgNPs.

A novel tridentate ligand nitrilotris(methylene)tris(1,2,3-triazole)triacetate (NTTTA) has been synthesized by click reaction and followed with ester hydrolysis reaction. The silver nanoparticles (AgNPs) were then modified and stabilized by this ligand, and subsequently been employed for the highly selective and sensitive colorimetric detection of Mn2+ in aqueous solution. The presence of Mn2+ can cause the aggregation of AgNPs, which leads to the color change of the dispersion from yellow to brown, as well as the decrease and red-shift of the surface plasmon resonance absorption. The detection limit of Mn2+ was as approximately 0.5 µM by the naked eyes. UV-vis spectroscopy analysis showed a good linear relationship between the logarithm of the ratios (A550/A395) and the concentration of Mn2+over the range of 0.05 µM-10 µM, and the LOD was calculated to be 12.6 nM (S/N = 3). The present assay showed good simplicity without the need of adjusting the pH value. The feasibility of this technique was evaluated for successful detection of Mn2+ in tap water and lake water samples, with good recoveries.

Cu2ZnSnS4/MoS2-Reduced Graphene Oxide Heterostructure: Nanoscale Interfacial Contact and Enhanced Photocatalytic Hydrogen Generation.

Hydrogen generation from water using noble metal-free photocatalysts presents a promising platform for renewable and sustainable energy. Copper-based chalcogenides of earth-abundant elements, especially Cu2ZnSnS4 (CZTS), have recently arisen as a low-cost and environment-friendly material for photovoltaics and photocatalysis. Herein, we report a new heterostructure consisting of CZTS nanoparticles anchored onto a MoS2-reduced graphene oxide (rGO) hybrid. Using a facile two-step method, CZTS nanoparticles were in situ grown on the surface of MoS2-rGO hybrid, which generated high density of nanoscale interfacial contact between CZTS and MoS2-rGO hybrid. The photoexcited electrons of CZTS can be readily transported to MoS2 through rGO backbone, reducing the electron-hole pair recombination. In photocatalytic hydrogen generation under visible light irradiation, the presence of MoS2-rGO hybrids enhanced the hydrogen production rate of CZTS by 320%, which can be attributed to the synergetic effect of increased charge separation by rGO and more catalytically active sites from MoS2. Furthermore, this CZTS/MoS2-rGO heterostructure showed much higher photocatalytic activity than both Au and Pt nanoparticle-decorated CZTS (Au/CZTS and Pt/CZTS) photocatalysts, indicating the MoS2-rGO hybrid is a better co-catalyst for photocatalytic hydrogen generation than the precious metal. The CZTS/MoS2-rGO system also demonstrated stable photocatalytic activity for a continuous 20 h reaction.

Dominant Factors Governing the Electron Transfer Kinetics and Electrochemical Biosensing Properties of Carbon Nanofiber Arrays.

Carbon-based electrodes have been widely used in electroanalysis for more than half a century, but the factors governing the heterogeneous electron-transfer (HET) rate are still unclear. The effects of the exposed edge plane site density, inherent resistance of the carbon electrode, and adjustable resistors on the HET kinetics of several outer- and inner-sphere redox couples including [Fe(CN)6]3-/4-, Ru(NH3)63+/2+, Fe3+/2+, dopamine, ascorbic acid, and uric acid are investigated using three kinds of carbon electrodes composed of core-shell quasi-aligned nanofiber arrays (QANFAs). The internal resistance is found to be a key factor affecting the HET kinetics and electrochemical biosensing properties. The electrodes exhibit high selectivity and sensitivity in dopamine detection in the presence of ascorbic acid and uric acid. In addition to the promising application to electrochemical biosensing, the core-shell TiC/C QANFAs encompassing a highly electroactive carbon shell and conductive TiC core provide insights into the design and construction of the ideal carbon electrode.

Au Nanoparticles Decorated TiO2 Nanotube Arrays as a Recyclable Sensor for Photoenhanced Electrochemical Detection of Bisphenol A.

A photorefreshable and photoenhanced electrochemical sensing platform for bisphenol A (BPA) detection based on Au nanoparticles (NPs) decorated carbon doped TiO2 nanotube arrays (TiO2/Au NTAs) is described. The TiO2/Au NTAs were prepared by quick annealing of anodized nanotubes in argon, followed by controllable electrodeposition of Au NPs. The decoration of Au NPs not only improved photoelectrochemical behavior but also enhanced electrocatalytic activities of the resulted hybrid NTAs. Meanwhile, the high photocatalytic activity of the NTAs allowed the electrode to be readily renewed without damaging the microstructures and surface states after a short UV treatment. The electrochemical detection of BPA on TiO2/Au NTAs electrode was significantly improved under UV irradiation as the electrode could provide fresh reaction surface continuously and the further increased photocurrent resulting from the improved separation efficiency of the photogenerated electron-hole pairs derived from the consumption of holes by BPA. The results showed that the refreshable TiO2/Au NTAs electrode is a promising sensor for long-term BPA monitoring with the detection limit (S/N = 3) of 6.2 nM and the sensitivity of 2.8 µA·µM(-1)·cm(-2).

Recyclable Non-Enzymatic Glucose Sensor Based on Ni/NiTiO3 /TiO2 Nanotube Arrays.

A non-enzymatic amperometric glucose sensor that can be renewed by light irradiation is described. It is composed of Ni/NiTiO3 /TiO2 nanotube arrays (NTAs) prepared by a simple hydrothermal treatment of as-anodized TiO2 NTAs in a nickel acetate solution followed by annealing under H2 /Ar. The Ni/NiTiO3 /TiO2 NTAs exhibit excellent electrocatalytic activity towards glucose oxidation in a 1.0 M NaOH supporting solution at a low applied potential of 0.4 V (vs. Ag/AgCl) with a high sensitivity of 456.4 µA cm-2 mM-1 and a low detection limit of 0.7 µM (S/N=3). The excellent electrochemical biosensing properties for glucose detection can be attributed to the orderly vertical alignment, large accessible surface, high conductivity, and electroactive NiII /NiIII redox couple. Meanwhile, owing to their high photocatalytic activity, Ni/NiTiO3 /TiO2 NTAs can readily decompose the organic fouling species generated on the electrode surface during glucose detection under light irradiation so that the original sensitivity and selectivity can be restored. The Ni/NiTiO3 /TiO2 NTAs electrode provides a promising renewable platform enabling long-term glucose monitoring with high sensitivity and selectivity.

Real-time monitoring of auxin vesicular exocytotic efflux from single plant protoplasts by amperometry at microelectrodes decorated with nanowires.

Recent biochemical results suggest that auxin (IAA) efflux is mediated by a vesicular cycling mechanism, but no direct detection of vesicular IAA release from single plant cells in real-time has been possible up to now. A TiC@C/Pt-QANFA micro-electrochemical sensor has been developed with high sensitivity in detection of IAA, and it allows real-time monitoring and quantification of the quantal release of auxin from single plant protoplast by exocytosis.

Label-free detection of endocrine disrupting chemicals by integrating a competitive binding assay with a piezoelectric ceramic resonator.

A piezoelectric biosensor for detection of endocrine disrupting chemicals (EDCs) was developed by incorporating chemical/biochemical recognition elements on the ceramic resonator surface for competitive binding assays. A facile electrodeposition was employed to modify the sensor surface with Au nanoparticles, which increased the surface area and enhanced the binding capacity of the immobilized probes. Thiol-labeled long chain hydrocarbon with bisphenol A (BPA) as head group was synthesized and self-assembled on the Au nanoparticle surface as the sensing probes, which showed a linear response upon the binding of estrogen receptor (ER-α) ranging from 1 to 30 nM. Detection of estrone, 17ß-estradiol and BPA was achieved by integrating a competitive binding assay with the piezoelectric sensor. In this detection scheme, different concentrations of EDCs were incubated with 30 nM of ER-α, and the un-bounded ER-α in the solution was captured by the probes immobilized on the ceramic resonator, which resulted in the frequency changes for different EDCs. The biosensor assay exhibited a linear response to EDCs with a low detection limit of 2.4-2.9 nM (S/N=3), and required only a small volume of sample (1.5 µl) with the assay time of 2h. The performance of the biosensor assay was also evaluated for rapid and facile determination of EDCs of environmental relevant concentrations in drinking water and seawater, and the recovery rate was in the range between 94.7% and 109.8%.

Vascular lumen simulation and highly-sensitive nitric oxide detection using three-dimensional gelatin chip coupled to TiC/C nanowire arrays microelectrode.

Reproducing the physiological environment of blood vessels for the in vitro investigation of endothelial cell functions is very challenging. Here, we describe a vascular-like structure based on a three-dimensional (3D) gelatin chip with good compatibility and permeability which is also cost-effective and easy to produce. The controllable lumen diameter and wall thickness enable close mimicking of blood vessels in vitro. The 3D gelatin matrix between adjacent lumens is capable of generating soluble-factor gradients inside, and diffusion of molecules with different molecular weights through the matrix is studied. The cultured human umbilical vein endothelial cells proliferate on the gelatin lumen linings to form a vascular lumen. The hemodynamic behavior including adhesion, alignment of endothelial cells (ECs) under shear stress and pulsatile stretch is studied. Furthermore, a microelectrode comprising TiC/C nanowire arrays is fabricated to detect nitric oxide with sub-nM detection limits and NO generation from the cultured ECs is monitored in real time. This vascular model reproduces the surrounding parenchyma of endothelial cells and mimics the hemodynamics inside blood vessels very well, thereby enabling potential direct investigation of hemodynamics, angiogenesis, and tumor metastasis in vitro.

Controllable growth of conical and cylindrical TiO2-carbon core-shell nanofiber arrays and morphologically dependent electrochemical properties.

Quasi-aligned cylindrical and conical core-shell nanofibers consisting of carbon shells and TiO(2) nanowire cores are produced in situ on Ti foils without using a foreign metallic catalyst and template. A cylindrical nanofiber has a TiO(2) nanowire core 30-50 nm in diameter and a 5-10 nm-thick cylindrical carbon shell, while in the conical nanostructure the TiO(2) nanowire core has a diameter of 20-40 nm and the thickness of the carbon shell varies from about 200 nm at the bottom to about 5 nm at the tip. Electrochemical analysis reveals well-defined redox peaks of the [Fe(CN)(6)](3-/4-) redox couple and heterogeneous charge-transfer rate constants of 0.010 and 0.062 cm s(-1) for the cylindrical and conical nanofibers, respectively. The coverage of exposed edge planes on the cylindrical and conical carbon shells is estimated to be 2.5 and 15.5 % respectively. The more abundant exposed edge planes on the conical nanofiber decrease the overpotential and increase the voltammetric resolution during electrochemical detection of uric acid and ascorbic acid. Our results suggest that the density of edge-plane sites estimated from Raman scattering is not necessarily equal to the density of exposed edge-plane sites, and only carbon electrodes with a large density of exposed edge planes or free graphene sheet ends exhibit better electrochemical performance.

Recyclable and high-sensitivity electrochemical biosensing platform composed of carbon-doped TiO2 nanotube arrays.

Electrode fouling and passivation are the main reasons for attenuated signals as well as reduced sensitivity and selectivity over time in electrochemical analysis. We report here a refreshable electrode composed of carbon-doped TiO(2) nanotube arrays (C-doped TiO(2)-NTAs), which not only has excellent electrochemical activity for simultaneous determination of 5-hydroxytryptamine and ascorbic acid but also can be easily photocatalytically refreshed to maintain the high selectivity and sensitivity. The C-doped TiO(2)-NTAs are fabricated by rapid annealing of as-anodized TiO(2)-NTAs in argon. The residual ethylene glycol absorbed on the nanotube wall acts as the carbon source and no foreign carbon precursor is thus needed. The morphology, structure, and composition the C-doped TiO(2)-NTAs are determined, and the corresponding doping mechanism is investigated by thermal analysis and in situ mass spectroscopy. Because of the high photocatalytic activity of the C-doped TiO(2)-NTAs electrode, the electrode surface can be readily regenerated by ultraviolet or visible light irradiation. This photoassisted regenerating technique does not damage the electrode microstructure while rendering high reproducibility and stability.